Hạn chế của crom hóa trị sáu ngăn cản việc sử dụng dây quấn từ thông (FCAW) ở hầu hết các nơi và hàn hồ quang kim loại khí (GMAW) thực hiện kém trong cả hai hướng hàn rãnh. Vì vậy, các nhà sản xuất nên làm gì để có được hiệu suất và độ tin cậy tốt hơn?

From material handling to cutting and welding, stainless steel (SS) usually brings some manufacturing difficulties. Let us quickly review the reasons for making stainless steel stainless.

There are several different SS groups, but usually carbon steel becomes a kind of stainless steel, in which chromium is added at a minimum of 10.5% by weight. The most common version of stainless steel is austenitic SS, which contains approximately 8% by weight of nickel. This improves corrosion resistance, serves as an austenite catalyst, and greatly improves toughness for low-temperature applications.

The austenitic SS series is classified as 18% chromium/8% nickel material, which can effectively resist environmental or chemical oxidation (rust) and corrosion. The choice of a special type of SS depends on its ability to provide the required mechanical properties under the conditions of use. These vary depending on the product concentration, operating temperature range or viscosity. Abrasion can greatly reduce the effectiveness of certain grades or types of stainless steel as a function of operating temperature.

Phân tích các vấn đề và chiến lược trong quá trình hàn thép không gỉ theo phương thẳng đứng

Regarding welding, the addition of chromium and nickel and other alloying elements is also the reason why welding SS is more challenging. These elements change the dynamics of the weld pool, one of which is the fluidity, which is caused by the arc energy transfer and changes in the surface tension of the molten weld pool. For these reasons, vertical upward welding (3G/F) or vertical downward welding becomes more challenging.

The primary goal of SS welding manufacturing is to find a suitable filler metal to meet the expected service conditions.

If necessary, the use of shielding gas should be considered under the required conditions of use. Assuming that all these conditions are met, the next goal is to use the welding process and filler metal to enable you to perform defect-free welding and optimize the deposition rate of the welding process.

For most applications, gas tungsten arc welding (GTAW), GMAW or FCAW for manual welding processes will be selected. GTAW produces some of the highest quality welds, but they are very slow in terms of deposition rate and travel speed, so we will not consider using them for the time being. Of course, for the purpose of simplifying equipment, on-site maintenance welding may also use shielded metal arc welding (SMAW), but we will focus on in-house manufacturing.

Since SS has a variety of chemical compositions far exceeding that of carbon steel, the chemical composition that is effective for one grade may not work for another. The specific grade of SS substrate required by the use conditions requires you to select filler metals that match or exceed the required mechanical properties.

Common problems of vertical downward welding are poor appearance of the weld bead, excessive spatter, poor weld toe overlap, lack of fusion and wash-out (or recessed) appearance. You can still create well-structured, leak-proof welds on thin materials, but overall, the sum of these variables may cause manufacturers to seek other solutions. Keep in mind that for materials with a thickness of less than 3/16 inch, vertical downward welding is the most common technique.

If the part you want to weld cannot be safely positioned, so the weld is in a horizontal or horizontal position (1G/F or 2G/F), 3G/F (vertically upward) may be the only option.

For thick-walled profiles, the best performance is to use GMAW or FCAW to weld vertically upwards. Compared with GMAW, the use of FCAW for welding does produce more smoke and smoke, but it does produce high-quality welds and a good deposition rate. Many companies use FCAW to weld SS and adopt appropriate engineering control measures to ensure the safety of welders. However, please consult your safety department and local industrial hygienist to ensure proper safety measures are taken and OSHA requirements are complied with.

Taking all factors into consideration, this makes GMAW an ideal process for SS welding. GMAW has two choices of wire selection: solid wire or metal core wire. For single-wire applications, the most common industry practice is to use 0.035-0.045-in.-dia. Solid line, 98% argon/2% carbon dioxide protective gas mixture and short-circuit transmission mode. You will need a constant voltage welding power supply with a steep slope and adjustable inductance to minimize welding spatter and allow greater molten pool fluidity when welding in the 3G/F position. This is essential for using this weld metal transfer mode to produce high-quality welds and beautiful appearance.

If your equipment can be welded by pulse transmission, you can use metal cored wire. Generally, the welding wire uses a 90% argon/10% carbon dioxide shielding gas mixture. You will want to use a diameter of 0.045 inches or 0.052 inches. The electrode and weld are in pulse mode.

In some applications, based on the material thicknesses discussed previously, the pulse transmission mode provides good results for other vertical upward welding through vertical downward welding. Depending on the manufacturer of the welding equipment and its pulse welding waveform, the quality and chemical properties of the filler metal, and the SS grade used, you must perform some experiments to find the welding parameters that produce the best results.

Liên kết đến bài viết này : Phân tích các vấn đề và chiến lược trong quá trình hàn thép không gỉ theo phương thẳng đứng

Tuyên bố Tái bản: Nếu không có hướng dẫn đặc biệt, tất cả các bài viết trên trang web này là bản gốc. Vui lòng ghi rõ nguồn để tái bản: https: //www.cncmachiningptj.com/,thanks!


Phân tích các vấn đề và chiến lược trong quá trình hàn thép không gỉ theo phương thẳng đứngTấm kim loại, berili, thép cacbon, magiê, 3D in, độ chính xác Cơ khí CNC dịch vụ cho các ngành thiết bị nặng, xây dựng, nông nghiệp và thủy lực. Thích hợp cho nhựa và hiếm gia công hợp kim. Nó có thể biến các bộ phận có đường kính lên đến 15.7 inch. Các quy trình bao gồm gia công thụy sĩ, chuốt, tiện, phay, doa và ren. Nó cũng cung cấp đánh bóng kim loại, sơn, mài bề mặt và thân cây dịch vụ ép tóc. Phạm vi sản xuất lên đến 50,000 chiếc. Thích hợp cho vít, khớp nối, mang, bơm, bánhhộp đựng, máy sấy trống và thức ăn quay van Ứng dụng.PTJ sẽ cùng bạn lập chiến lược để cung cấp các dịch vụ hiệu quả nhất về chi phí nhằm giúp bạn đạt được mục tiêu của mình, Chào mừng bạn đến với Liên hệ với chúng tôi ( [email protected] ) trực tiếp cho dự án mới của bạn.

Trả lời

Email của bạn sẽ không được hiển thị công khai. Các trường bắt buộc được đánh dấu *